Equipment 3: technical climbing hardware
On Everest, the personal hardware list is short but critical: harness, helmet, ice axe, ascender, descender, carabiners, and tethers. The expedition team supplies the fixed ropes, anchors, and ladders. Every item you carry must be certified to UIAA or CE/EN safety standards and must work with thick mitts.
Personal hardware list
| Item | Quantity | Key specification | Why |
|---|---|---|---|
| Alpine climbing harness | 1 | Adjustable leg loops that open fully; fits over the down suit | You must put it on over bulky clothing, often with crampons on |
| Helmet | 1 | UIAA/CE certified; fits over a warm hat | Falling ice and rock in the icefall and on the Lhotse Face |
| Mountaineering ice axe | 1 | 55-70 cm, classic straight or slightly curved shaft | Walking support, self-arrest; little used on fixed ropes |
| Ascender (jumar) | 1 | Handled ascender, large handle for mitts | Climbing fixed ropes |
| Descender | 1 | Figure-8 or tube-style belay device | Rappelling fixed ropes on the descent |
| Locking carabiners | 3-4 | Large, pear-shaped (HMS), easy to operate with mitts | Tethers, rappel device, anchors |
| Non-locking carabiners | 2-4 | Wiregate for low weight | Gear, spare use |
| Safety tethers (cowtails) | 2 | Dynamic rope or purpose-made lanyards, lengths set to your arm reach | Connecting to fixed ropes |
| Prusik cords | 2 | 5-6 mm accessory cord | Backup ascender, rescue |
| Slings | 2 | 120 cm sewn slings | Anchors, extensions |
| Headlamp | 1 + spare | 300+ lumens, lithium batteries, works in cold | Summit night and icefall starts |
Choosing and setting up your ascender and tethers
- Use a left- or right-handed ascender matching your dominant hand.
- The long tether attaches to the ascender. Its length should let you reach the ascender at arm's length above your head, but not further.
- The short tether attaches to a locking carabiner and keeps you close to the rope.
- Some climbers prefer purpose-made adjustable lanyards; others tie their tethers from dynamic rope with figure-eight knots. Ask your instructor to check your setup.
Hardware for training peaks (not always needed on Everest)
| Item | Use |
|---|---|
| Technical ice tools (2) | Steeper ice routes, some training peaks |
| Ice screws (4-6) | Anchors on ice |
| Snow pickets (2) | Anchors in snow |
| Dynamic rope (for team) | Roped glacier travel, crevasse rescue |
| Pulley and progress-capture device | Crevasse rescue hauling systems |
| Belay device with guide mode | Belaying partners on training climbs |
Standards and inspection
- UIAA (International Climbing and Mountaineering Federation) and CE/EN markings show the product passed safety tests. Buy from reputable sellers; fake climbing gear is sold online and in some markets.
- Inspect gear before each trip: look for cracks, sharp edges, worn stitching on harness and slings, and gates that do not close smoothly.
- Soft goods (harnesses, slings, tethers) age over time. Follow the manufacturer's recommended lifespan, commonly up to about 10 years from manufacture even if unused, and much less with heavy use.
- Retire any carabiner that has been dropped a long way onto rock or shows cracks.
Well-known hardware brands
Petzl, Black Diamond, Grivel, Camp, Edelrid, Mammut, DMM, and Singing Rock all make certified mountaineering hardware. Decathlon's Simond brand offers budget options in India for training use.
Ice axe types and sizing
| Type | Shaft | Use |
|---|---|---|
| Classic mountaineering axe | Straight, 55-70 cm | Walking, self-arrest, snow slopes; the standard for Everest and training peaks |
| Technical mountaineering axe | Slightly curved, 50-60 cm | Steeper snow and ice, mixed ground |
| Ice tools (pair) | Strongly curved, 45-50 cm | Vertical ice climbing; not needed on Everest's normal route |
Sizing: a traditional guide is that, standing upright with the axe held by its head at your side, the spike should reach roughly your ankle. Many modern climbers choose a slightly shorter axe for steeper ground. A B-rated (basic) axe is fine for general mountaineering; a T-rated (technical) axe is stronger for steeper terrain.
Leash or no leash: a leash prevents losing the axe on steep ground but can be awkward on fixed ropes. Many Everest climbers use a lightweight leash clipped to the harness.
Harness fitting
- Put the harness on over your summit clothing (down suit) at home.
- The waist belt sits above your hip bones and is tight enough not to slide down.
- Leg loops should open fully (buckles or clips), so you can put them on while wearing crampons.
- Double-check buckle threading each time (many modern harnesses have self-locking buckles, but check anyway).
- Gear loops should hold your ascender, descender, and carabiners within easy reach.
Helmets
- Hardshell helmets are durable and handle knocks well; foam (in-mould) helmets are lighter.
- Must fit over a warm hat or balaclava with room to adjust.
- Headlamp clips on the helmet are essential for night climbing.
- Replace after any significant impact, even if no damage is visible.
Ascenders and descenders in more detail
| Device | Detail |
|---|---|
| Handled ascender | The standard for fixed-rope climbing; toothed cam grips the rope |
| Chest ascender | Used in caving and some technical ascents; rarely used by Everest clients |
| Figure-8 descender | Simple, works well with thick or icy ropes, good heat dissipation, but twists ropes |
| Tube belay device (ATC type) | Lighter, versatile, used for belaying on training climbs |
| Assisted-braking devices | Useful for belaying on rock; not standard on Everest |
Gear care and storage at home
- Store hardware and soft goods in a cool, dry, dark place, away from chemicals and UV light.
- Wash harnesses and slings in lukewarm water with mild soap only; air dry.
- Keep a gear log with purchase dates, number of trips, and any falls or damage.
- Oil carabiner gates and ascender cams lightly with a manufacturer-approved lubricant if they stick (and wipe off the excess, since oil attracts dirt).